LEO
LEO is a hand-held meter for IVF application. It allows measurement of CO2-O2 gas composition, temperature, relative humidity, and gas flow of high-top and bench-top incubators, by using multiple sensor modules.
The CO2-O2-MODULE is embedded into LEO as a standard feature. The CO2-O2-MODULE can be easily extracted and sent to Okolab for re-calibration. Other (external) sensor modules can be connected to LEO’s connection ports.
LEO allows organization of the stored data, associating a label to each device connected. You can store up to 40 devices. The stored data can be displayed on LEO’s screen, organized by date and device.
Features
• Included CO2-O2-MODULE
• User-friendly, touch-screen interface
• Compatible with any incubator on the market
• Diffusion or Aspiration gas sampling modes
• Sampling tube and de-humidification kit included
• Long term logging and single point measurement
• USB OTG for data downloading to a USB flash drive
• Two external sensor connections to connect up to two optional sensor modules at the same time
• Software Update is available online so that LEO always has the latest software version
• Optional sensor modules are available
Available Sensors
• CO2-O2-MODULE (included with LEO)
• T1-MODULE
• T2-MODULE
• CO2-PPM-MODULE
• HUMIDITY-MODULE
• FLOW-RATE-MODULE
Gas Sampling Modes
Diffusion sampling mode
Gas flows into LEO through the dedicated diffusion port with
icon hand-held-meter-leo-diffusion-icon.
The minimum operating flow rate is 30 ml/min.
Aspiration (Pump) sampling mode
Gas is actively pulled in via LEO’s internal pump through the dedicated aspiration port with icon hand-held-meter-leo-diffusion-icon.
The pump flow rate can be set in the range 60-260 ml/min.
Diffusion / Aspiration Mode Selection
Single Point
Time Sequence
Gas Measurement From Wet Incubator
The Moisture Trap (included with LEO) is used when the measured gas is wet, in order to remove water molecules for protection of the gas sensors.
By using Wet Mode, LEO can improve the CO2 ad O2 readings by accounting for the water content of your incubator. The temperature and relative humidity (RH) values of your incubator must be entered.
Leo Equipped w/ Moisture Trap
Wet Measurement Mode
LEO Sensor Modules
The sensor modules are calibrated by using traceable standards, and stores the calibration data in the internal memory. The sensor modules can be delivered with traceable or accredited calibration certificate, and sent to Okolab for re-calibration.
Moreover, sensor calibration can be performed by using LEO through intuitive user calibration routines.
Each sensor can perform single point measurements and logging over time, and can store data in LEO’s local memory. The stored data can be displayed on LEO’s screen, organized by date and device. The stored data can be downloaded through the micro USB port and analyzed by using the LEO DATA IMPORT Excel Macro.
IVF Sensor Modules & Leo
CO2-O2-MODULE
CO2-02-Module
CO2-02-Module Housing
The CO2-O2-MODULE measures the CO2-O2 volume concentration in the unit of %, and CO2-O2 partial pressure in the units of mbar, psi and KPa. It is included in LEO and stores calibration data in its internal memory.
The CO2-O2-MODULE can be easily extracted and sent to Okolab for re-calibration. Moreover the CO2-O2-MODULE can be calibrated with an intuitive user calibration procedure. The CO2-O2-MODULE lifetime is 5 years.
T1 - MODULE
Small, flexible, calibrated, and immersible thermocouple. Ideal for measurements in liquids, such as culture media in a dish. T1-MODULE has a negligible diameter (0.13mm) and it can be directly introduced into an incubator, even if it lacks a dedicated temperature measurement port.
Features:
Sensor: K-type thermocouple
Measurement range: 0-60°C
Accuracy: ±0.1°C from 20 to 50°C
T2 - MODULE
Temperature probe, ideal for measurements of incubator temperature when sampling port access is available. T2-MODULE has an external diameter of 2 mm and is suitable for temperature measurements of bench-top and high-top incubators where the temperature monitoring port has a diameter larger than 2 mm.
Features:
Sensor: PT1000 RTD Class A
Measurement range: 0-60°C
Accuracy: ±0.1°C from 20 to 50°C
CO2-PPM-MODULE
Designed to measure carbon dioxide at ppm in offices, laboratories, hospitals, and generally, wherever indoor air quality is important for the occupants’ comfort and health. The probe is temperature and pressure compensated.
Features:
Sensor: Non-dispersive infrared (NDIR)
Measurement range: 0-10000 ppm
Accuracy: ±(50ppm +3% reading)
Response time: 2 minutes
HUMIDITY MODULE
Designed to measure carbon dioxide at ppm in offices, laboratories, hospitals, and generally, wherever indoor air quality is important for the occupants’ comfort and health. The probe is temperature and pressure compensated.
Features:
Sensor: Non-dispersive infrared (NDIR)
Measurement range: 0-10000 ppm
Accuracy: ±(50ppm +3% reading)
Response time: 2 minutes
FLOW RATE MODULE
Compact and accurate flow meter with short response time, ideal for instantaneous gas flow measurements. The highly compact and lightweight design makes it ideal for many different work environments. The presence of display allows to use the sensor module also as a standalone device.
Features:
Sensor:MEMS
Measurement range: 0-200 ml/min
Accuracy: ± (2.0 reading +0.5% full scale)
Repeatability: ±0.5% full scale
Response time:
Working pressure: 0.08-0.8 bar
Working temperature: -10 + 55°C
Calibration medium: air
REQUIRED CONTROLLERS
H401-T-CONTROLLER
2-Channel Temperature Controller with 4.3'' touch screen interface compatible with all H401 heating devices. One controller can control independently up to two items.
External temperature sensor (included) and self calibration routines allows easy calibration of the heating devices for the highest accuracy on sample temperature.
On board data logging and download procedures to USB drives allow to record temperature as a function of time and to log calibration events and alarms.
The controller is equipped with password protected routines to re-calibrate the sensors against certified thermometers.
Features
T - range: from ambient to 60°C
T - accuracy on specimen: ± 0.3°C
4.3'' touch screen interface
External T - sensor (included)
On-board Data logging and download routines to USB drive
On-board logging of calibration and alarm events
Alarm buzzer and External Alarm Connector
One controllers can control independently up to two devices
Self calibration routines allow to improve temperature accuracy
Password protected procedure for periodic calibration against certified thermometer
H401-T-PENNY
H401-T-PENNY is a compact single-channel Temperature Controller compatible with any OKOLAB heating device that combines performance and simplicity at an unbeatable price.
Features
Temperature range: from ambient to 60°C
Set point resolution: 0.1°C
Calibration via addition of offset
Maximum Output: 60 W
Dimensions: 83.65x45.05x20.20 mm
Weight: 47.50 g
NextGen LifeLabs provides specialized, innovative equipment, services, and support for the modern ART laboratory.
CONTACT US
384 Nina Way
Warminster, PA 18974
> Terms & Conditions
© 2020 Copyright NEXTGEN - All Rights Reserved.